Boat Mold & Mildew Remover / Preventer
$50.00 inc GST
Description
- Boat mold cleaner that attacks and removes mold on boats
- Remains active for months inhibiting the growth of new mold spores
- Eliminates all organic mold and mildew odours
“A true breakthrough product.”
Product Details
OUR BOATS ARE A FAVORITE PLACE FOR MOLD SPORES! A 5-STAR HOTEL!
Airborne mold spores are everywhere and in a warm and damp environment (such as our boats), they will settle on a surface and begin their new life maturing into mold.
A perfect example of this “environment” occurs almost every night on boats kept in or near the water – the calm and very humid air leaves a thick layer of dew on practically every exterior surface. A towel hung over a seat to dry after swimming will absorb the overnight dew and in the morning is wet. Our decks, vinyl seats, windshields, etc are all coated with a thick layer of dew. But the towel and these exterior surfaces will dry from the sun and fresh air.
However, this same damp, humid air also reaches other areas of our boats that are not exposed to the direct sun and abundant refreshed air. Enclosed cabins, the head, storage lockers, closets and cabinets, and the numerous “absorbent” surfaces like carpet, upholstered furniture, bedding, towels, clothing, etc. – these are prime areas for mold growth.
Familiar Greetings from Onboard Mold.
Mold certainly lets us know when it is present – sometimes visually, but always with a nose full of that familiar musty smell – like opening the canvas enclosure or the cabin door or a storage locker – especially after being closed-up for a few days. Or maybe when you open a cabinet drawer or closet in the stateroom and pull out a favorite tee shirt, pull it over your head and whoa! what is that stink??
Plain and simple… these odors are caused by actively growing mold and the gases it emits called Microbial Volatile Organic Compounds (aka MVOC’s). And as disgusting as it may be, these MVOC’s are the “waste product” left by healthy, growing mold.
Call it what you want, but the bottom line is we need to put an end to the healthy, growing mold onboard our boats. And this IS accomplished with the Boat Brite Mold & Mildew Remover / Preventer for boats!
Directions for Use
HERE’S HOW IT WORKS:
The Boat Brite Mold & Mildew Remover and Preventer’s mold-fighting ingredients are suspended in an ingenious humidity-sensitive polymer. With as little as 10% humidity the ingredients are activated – higher humidity levels release more of the ingredients. A liberal spray of the boat mold and mildew remover will leave an invisible “bio-shield” on a surface which would normally offer mold spores food and a place to mature into mold. When mold spores land on a surface treated with the boat Mold & Mildew Remover and Preventer, the active ingredients in the formulation immediately disable the spores and inhibit their growth and existence.
On existing boat mold when the Mold & Mildew Remover / Preventer is sprayed on it, the polymer encapsulates the mold, releasing the active ingredients to do their job.
This mold and mildew protection for boats will last for extended periods of time and will sustain through literally thousands of these mold spore invasions.
This photo was taken in the Boat Brite lab. It represents how the Mold & Mildew Remover and Preventer attacks mold even beyond where the product is directly applied.
Boat Brite Boat Mold & Mildew Remover / Preventer example
Using a Q-tip, the two dishes were “painted” with mold that Boat Brite grew from spores. They then laid absorbent circular wafers onto the middle of the dishes – one of the wafers was moistened with the Boat Brite Mold & Mildew Remover / Preventer. As you can see the dish with the moistened wafer is virtually mold free with only a couple of small spots of mold around the outside edge of the dish. The other dish remains covered with mold.
This demo shows that if you have an existing boat mold problem the Boat Brite Mold & Mildew Remover and Preventer will end the problem. And it also shows that if you accidentally miss a spot with the mold prevention spray, protection extends slightly past the sprayed area.
Re-Application Frequency:
The Boat Brite Mold & Mildew Remover and Preventer for boats should be re-applied as a routine preventive-maintenance program to keep the mold and mildew protection intact without interruption. We recommend to reapply every 2-3 months, however in high traffic areas and persistent hot and humid climates, a monthly reapplication will assure the mold and mildew protection remains consistent.
